• Pure sine wave inverter
  
• Output power factor 1
• Built in 1500W MPPT solar charge controller. Recommended for backup or solar.
• Selectable input voltage range for home appliances and personal computers
• Selectable charging current based on application
• Configurable AC/Solar input priority via LCD setting
• Compatible to mains voltage or generator power
• Auto restart while AC is recovering
• Overload and short circuit protection
• Battery equalization for optimized battery performance and life-cycle 
• Cold start function
• NOT Parallel compatible 
• Recommended for backup purposes and/or solar

Click here for technical specifications

Specifications and features
Product Code	SOL-I-AX-3MPLUS24
Model	Axpert MKS 3K-24 Plus
RATED POWER	3000VA/2400W
INPUT
Voltage	120 VAC or 230 VAC
Selectable Voltage Range	95-140 VAC or 170-280 VAC (For Personal Computers)
	65-140 VAC or 90-280 VAC (For Home Appliances)
Frequency Range	50 Hz/60 Hz (Auto sensing)
OUTPUT
AC Voltage Regulation (Batt. Mode)	110/120 VAC ± 5% (User selectable) or 230VAC ± 5%
Surge Power	6000VA
Efficiency (Peak)	90% - 93%
Transfer Time	10 ms (For Personal Computers) ; 20 ms (For Home Appliances)
Waveform	Pure sine wave
BATTERY & AC CHARGER
Battery Voltage	24 VDC
Floating Charge Voltage	27 VDC
Overcharge Protection	31 VDC
Maximum Charge Current	20 A or 20 A / 30 A
SOLAR CHARGER
Maximum PV Array Power	1500 W
MPPT Range @ Operating Voltage	30~ 115 VDC or 60 ~ 115 VDC
Maximum PV Array Open Circuit Voltage	145 VDC
Maximum Charging Current	60A
Maximum Efficiency	0.98
Standby Power Consumption	2 W
PHYSICAL
Dimension, D x W x H (mm)	140 x 295 x 479
Net Weight (kgs)	11.5
OPERATING ENVIRONMENT
Humidity	5% to 95% Relative Humidity(Non-condensing)
Operating Temperature	0°C - 55°C
Storage Temperature	-15°C - 60°C

NOTE:

All inverters must be installed by a qualified electrical wireman or Master electrician with a valid registration with the Department of Labour. A valid electrical certificate of compliance (Coc) must be issued once installed, specific to the installation of the backup or solar system. The installation must be compliant with SANS 10142 and ALL its parts. Any warranty claim submitted without installation photos, a valid Coc and proof of a qualified wireman/master electrician installing the unit, can be rejected and will render the warranty claim null at void.

The warranty does not cover damage resulting from:

• ·         Power surge
• ·         Under-voltage
• ·         Over-voltage
• ·         Lightning
• ·         Corrosion
• ·         Sea spray
• ·         Condensation
• ·         Water damage
• ·         Dust or any solid particles
• ·         Sand
• ·         Insects
• ·         Lizards
• ·         Excessive heat exposure
• ·         Weather damage
• ·         Negligence by the installer or homeowner
• ·         Incorrect installation
• ·         Inadequate protection device rating
• ·         Tampering (broken seal)
• ·         Dirty filters
• ·         Exceeding the maximum power rating, current or voltage for the input solar circuit, DC battery input, AC input and AC output.

The warranty will be void if the unit is:

• ·         Not installed as per manufacturers specifications
• ·         Not installed with a minimal 40kA surge protection unit for both live and neutral wires from the AC incoming supply
• ·         Not installed with a minimal 40kA surge protection unit for both positive and negative wires from the AC incoming supply
• ·         Not protected by the calculated and required 2 pole breakers for the input and output of the inverter
• ·         Not installed with a changeover switch
• ·         The battery input must be protected by a rated fuse for both the negative and positive connections, within the calculated PSCC ratings.
• ·         Tampered with (attempted to open the unit)
• ·         Visible damage to the unit